Application: Operating cost divider wastewater associations

The allocation of operating costs in waste water special-purpose associations according to the polluter-pays principle is becoming increasingly important. Especially in association areas with a high proportion of extraneous water, a volume-proportional division of operating costs is advantageous because it creates an incentive for the elimination of extraneous water. We support you with measuring concepts, data transmission and recording, as well as during the operation of the measuring points.

Temporary measurements to collect reliable measurement data.

Measurement campaigns

For temporary measurement campaigns, we provide you with an extensive rental pool of over 50 measuring devices with different nominal diameters and measuring methods. Using modern data transmission technology, all measured values are transferred directly and securely to the online process performance system. You will receive temporary access for the measurement campaign and can view the data online at any time.
Drainage control for waste water with pneumatic drive
Robust, transparent, accurate, fast, low maintenance and reliable for wastewater, raw wastewater and rainwater.

IDM-based pneumatic outflow control

Precise drain throttle for heavily polluted waste water. The IDM flow measurement for full filling is the central element of the almost self-cleaning, remotely operated and highly precise pneumatic discharge control PNA. The reliable and never-tiring flap with pneumatic drive and the pinch valve react quickly to changing flows and conditions.
LDM partially filled waste water flow measurement
Highly Precise Ultrasonic transit-time difference flow measurement for wastewater, raw wastewater and rainwater

LDM partially filled Flow measurement

Highly precise flow value acquisition. The LDM is a calibrated measuring device for backflow-free flow measurement of waste water in open channels or free flowing lines. 10 flow velocity measuring sections distributed over the entire cross section provide most accurate flow values when the sensor is partially or fully filled. The level measurement is integrated in the device housing.
LDM-controlled pneumatic discharge control with, throttle with partially filled flow measurement
Flow measurement and discharge control for wastewater, raw wastewater and rainwater in partially and fully filled pipes.

LDM-based pneumatic discharge control

Most reliable waste water throttle and discharge control with accurate flow measurement for partial filling and dry installation. The fast, almost self-cleaning and remotely controllable pneumatically driven pinch valve is based on the LDM flow measurement integrated in the system and limits waste water, raw waste water and rainwater quantities to a value that can be set as required.
Pneumatic discharge control partially filled TFPNA as rainwater basin control in the sewer system
The reliable discharge control for wastewater and rainwater

Pneumatic discharge control partly filled TF-PNA

Precise and easy to maintain throttle system for stormwater tanks and wastewater structures. The fast, almost self-cleaning and remotely controllable butterfly valve with pneumatic actuator is based on the flow measurement integrated in the system and limits the flow to an arbitrarily adjustable quantity. As long as the maximum flow is not reached, the flap remains open, while the flow measurement system measures precisely even when partially filled.
Portable flow measurement for wastewater and external water
Temporary use of the proven MID for full filling to collect high-precision measurement data.

Portable flow measurement with MID

Waste water and external water flow measurement Measurements are performed with a high-precision, portable MID flowmeter mechanically protected by a plastic layer, which is normally installed in existing shafts and ducts without structural modifications. A bypass cushion completely seals the channel cross section and guides the entire water quantity completely through the measuring system.
Stationary flow measurement for waste water quantity measurement
Special solutions for measuring wastewater, raw wastewater and rainwater under the most difficult conditions.

Stationary flow measurement for wastewater

When the impossible becomes possible. High flow velocities, steep gradients, tight spaces, large measuring range. The more difficult the measuring task, the more suitable is the stationary flow measurement, which can often be retrofitted in existing structures and shafts.
for a wide range of measurement tasks in wastewater, drinking water, industrial and water body applications

STEBAnet mobile

Our data loggers are compact transmission devices that can accommodate up to four sensors, which can be connected either via cable or remotely via Bluetooth. The data collected is transmitted via mobile networks to the online or local process control system. Thanks to their low power consumption, the devices are ideal for operating decentralised measuring points.
TF stationäre Durchflussmessung teilgefüllt für Abwasser und Regenwasser
Ultrasonic transit time difference measurement with dry weather gutter

TF Stationary flow measurement partially filled

The TF Stationary Flow Measurement is a calibrated measuring channel for backflow-free flow measurement of wastewater, raw wastewater and rainwater in open channels or open channels.
Non-intrusive ultrasonic flow measurement for closed and fully filled pipelines.

Clamp-on flow measurement

Flow measurement on the outer wall of the pipe. With a flowmeter with clamp-on transducers it is possible to measure the flow in pipes simply from the outside. The transducers are installed on the pipeline with little technical effort and without process interruption. Rotationally symmetric flow profiles can be measured with only one acoustic section; non-symmetric ones require the use of several sections.
Industrial electrical installation in wet and corrosive environments
Resistant electrical engineering in wet, corrosive, explosive and aggressive environments

Electrical installations and controls

As a licensed electrical installation company, we offer the highest installation quality with special products and equipment for durable and trouble-free installations.
General equipment for wastewater and drinking water engineering structures
Holistic solutions for highest quality and simple project structures.

General Equipment

With a company history that began in the 1960s, we are one of the leading companies in the project planning and realisation of reliable, precise and holistic solutions in the automation industry. Our project team consists of automation, electrical and software engineers, design and mechanical engineers, project managers, as well as installers and service technicians.

Offers, solutions and services

On our overview page you can easily get to know our wide range of products and filter as you wish:

Overview offers

Topics

Search

Search

Industries

Wastewater treatment, sewage plant, sewerage system and external structures
Steam and hot water systems
District heating
Running water / watercourse regulation
Stormwater treatment
Drinking water supply
Hydropower plants

Field of application